- 您现在的位置：买卖IC网 > Sheet目录868 > LTM4605EV#PBF (Linear Technology)IC DC/DC UMODULE 5A 141-LGA
LTM4605
APPLICATIONS INFORMATION
output voltage falls by more than 70%, then the maximum
output current is progressively lowered to about 30% of
its full current limit value for boost mode and about 40%
for buck mode.
Standby Mode (STBYMD)
The standby mode (STBYMD) pin provides several choices
for start-up and standby operational modes. If the pin is
pulled to ground, the SS pin is internally pulled to ground,
preventing start-up and thereby providing a single control
pin for turning off the controller. If the pin is left open or
decoupled with a capacitor to ground, the SS pin is internally
provided with a starting current, permitting external control
for turning on the controller. If the pin is connected to a
voltage greater than 1.25V, the internal regulator (INTV CC )
will be on even when the controller is shut down (RUN
pin voltage <1.6V). In this mode, the onboard 6V linear
regulator can provide power to keep-alive functions such
as a keyboard controller.
INTV CC and EXTV CC
An internal P-channel low dropout regulator produces 6V
at the INTV CC pin from the V IN supply pin. INTV CC powers
the control chip and internal circuitry within the module.
The LTM4605 also provides the external supply voltage pin
EXTV CC . When the voltage applied to EXTV CC rises above
5.7V, the internal regulator is turned off and an internal
switch connects the EXTV CC pin to the INTV CC pin thereby
supplying internal power. The switch remains closed as long
as the voltage applied to EXTV CC remains above 5.5V. This
allows the MOSFET driver and control power to be derived
from the output when (5.7V < V OUT < 7V) and from the
internal regulator when the output is out of regulation (start-
up, short-circuit). If more current is required through the
EXTV CC switch than is speci?ed, an external Schottky diode
can be interposed between the EXTV CC and INTV CC pins.
Ensure that EXTV CC ≤ V IN .
The following list summarizes the three possible connec-
tions for EXTV CC :
1. EXTV CC left open (or grounded). This will cause INTV CC
to be powered from the internal 6V regulator at the cost
of a small ef?ciency penalty.
2. EXTV CC connected directly to V OUT (5.7V < V OUT < 7V).
This is the normal connection for a 6V regulator and
provides the highest ef?ciency.
3. EXTV CC connected to an external supply. If an external
supply is available in the 5.5V to 7V range, it may be
used to power EXTV CC provided it is compatible with
the MOSFET gate drive requirements.
Thermal Considerations and Output Current Derating
In different applications, the LTM4605 operates in a variety
of thermal environments. The maximum output current is
limited by the environmental thermal condition. Suf?cient
cooling should be provided to ensure reliable operation.
When the cooling is limited, proper output current derating is
necessary, considering ambient temperature, air?ow, input/
output condition, and the need for increased reliability.
The power loss curves in Figures 5 and 6 can be used
in coordination with the load current derating curves in
Figures 7 to 12 for calculating an approximate θ JA for
the module. Column designation delineates between no
heat sink, and a BGA heat sink. Each of the load current
derating curves will lower the maximum load current as
a function of the increased ambient temperature to keep
the maximum junction temperature of the power module
at 115°C maximum. This will allow a safe margin to work
at the maximum operating temperature below 125°C.
Each of the derating curves and the power loss curve that
corresponds to the correct output voltage can be used to
solve for the approximate θ JA of the condition. A complete
explanation of the thermal characteristics is provided in
the thermal application note for the LTM4605.
DESIGN EXAMPLES
Buck Mode Operation
As a design example, use input voltage V IN = 12V to 20V,
V OUT = 12V and f = 400kHz.
Set the PLLFLTR pin at 2.4V or more for 400kHz frequency
and connect FCB to ground for continuous current mode
operation. If a divider is used to set the frequency as shown
in Figure 14, the bottom resistor R3 is recommended not
to exceed 1k.
4605fc
13
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LTM4606MPV#PBF
IC DC/DC UMODULE 6A 133-LGA
LTM4607IV#PBF
IC BUCK/BOOST SYNC ADJ 5A 141LGA
LTM4608AEV#PBF
IC BUCK SYNC ADJ 8A 68LGA
LTM4608IV#PBF
IC DC/DC UMODULE 8A 68-LGA
LTM4609IV#PBF
IC BUCK/BOOST SYNC ADJ 4A 141LGA
LTM4612IV#PBF
IC BUCK SYNC ADJ 5A 133LGA
LTM4613MPV#PBF
IC UMODULE DC/DC 8A 133-LGA
LTM4614IV#PBF
IC UMODULE DC/DC DUAL 4A 144LGA
相关代理商/技术参数
LTM4605EV#PBF
制造商:Linear Technology 功能描述:IC SMPS CONTROLLER CURRENT-MODE LGA
LTM4605EVPBF
制造商:Linear Technology 功能描述:Conv DC-DC Step Up Step Down
LTM4605EV-PBF
制造商:LINER 制造商全称:Linear Technology 功能描述:High Effi ciency Buck-Boost DC/DC μModule
LTM4605IV#PBF
功能描述:IC DC/DC UMODULE 5A 141-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:21V 电压 - 输入（最大）:32V Voltage - Output 1:5V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:100W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:*
LTM4605IV#PBF
制造商:Linear Technology 功能描述:DC/DC MICRO MODULE IC
LTM4605IVPBF
制造商:Linear Technology 功能描述:Conv DC-DC Step Up Step Down
LTM4605IV-PBF
制造商:LINER 制造商全称:Linear Technology 功能描述:High Effi ciency Buck-Boost DC/DC μModule
LTM4605RD
功能描述:LED 电路板指示器 Vert LED Assmbly 5mm Red RoHS:否 制造商:Lumex LED 大小:3 mm 照明颜色:Green 波长:565 nm 光强度:30 mcd 安装类型:SMD/SMT 显示角:60 deg 封装:Reel